Results
To View Documents: Select from the language listed per sheet
 AD-01 Supplementary Cementitious Materials |
|
| AD-02 Cold Weather Concrete Practices |
|
| AD-03 Hot Weather Concrete Practices |
|
| AD-04 Set Retarding Admixtures |
|
| AD-05 Shrinkage Control Additives |
|
| AD-06 MODIFIED ASTM C157 TEST METHOD |
|
| AD-07 Offsetting Potential Corrosive Effects of Chlorides Using Eucon CIA |
|
| AD-08 What is PLC or Type IL? |
|
| CP-01 Chemical Grouts Hydrophobic vs Hydrophilic |
|
| CP-02 Chemical Resistance of Cured Eucolastic Sealants |
|
| CP-03 Coating Defects Caused by Concrete Outgassing |
|
| CP-04 Cold Temperature Installation of Joint Fillers |
|
| CP-05 Concrete Sealer Troubleshooting |
|
| CP-06 Eucolastic 1SL and Jet Fuel Resistance |
|
| CP-07 Eucolastic Sealants Paintability |
|
| CP-08 Eucolastic Sealants Maintenance Instructions |
|
| CP-09 Eucolastic Sealants ASTM C 920 Cold Weather Installation Recommendations |
|
| CP-10 Eucolastic Sealants ASTM C 920 |
|
| CP-11 Exterior Use of Dry Shake Hardeners |
|
| CP-12 Installation of Eucolastic 1SL on Green Concrete |
|
| CP-13 Joint Filler Bubbling |
|
| CP-14 Joint Filler Elongation Separation and Repair |
|
| CP-15 Latex Bonding Agents |
|
| CP-16 Maintenance of a Diamond Hard Treated Floor |
|
| CP-17 Maintenance of Euclid Chemical Epoxy and Urethane Floor Coating System |
|
| CP-18 Sealants VS Joint Fillers |
|
| CP-19 Silane and Siloxane Water Repellents for Concrete and Masonry |
|
| CP-20 Silicates, Siliconates, and Fluorosilicates Explained |
|
| CP-21 Solvent Based Sealer Technical Tip |
|
| CP-22 Tire Marking Pickup of Concrete Sealers |
|
| CP-23 Using Epoxy Coatings in Cold Weather |
|
| CP-24 Water Based Sealers: Guide to Successful Application |
|
| CP-25 Duralprep A.C. Compressive Strength |
|
| CP-26 Epoxy vs Polyurea Joint Fillers |
|
| CP-27 Standard Floor Joint Filling Details |
|
| CP-28 Wet Mils Conversion Chart |
|
| CP-30 Efflorescence - Causes, Prevention, and Removal |
|
| CP-29 Epoxy Guide |
|
| FC-01 Difference Between Micro and Macro Fibers |
|
| FC-02 Tuf-Strand SF Slab on Ground Design for Temperature & Shrinkage Crack Control |
|
| FC-03 Thin Wall and Precast Design for Bending Moment Steel Conversion |
|
| FC-04 FAQs on Slump, Air Content and Compressive Strength when using TUF-STRAND SF |
|
| FC-05 FAQs on Steel Fibers vs. Synthetic Fibers |
|
| FC-06 FAQs on Fiber Types and Mixing Problems |
|
| FC-07 FAQs on Concrete Thickness and Finishing |
|
| FC-08 FAQs on Technical Issues when using Fibers |
|
| FC-09 FAQs on Secondary Reinforcement and Composite Steel Deck Systems |
|
| FC-10 FAQs on Pumping and Finishing Fiber Reinforced Concrete |
|
| FC-11 Performance-Based Specifications for Fiber Reinforced Concrete |
|
| FC-12 Recommended Practices for Addition of TUF-STRAND SF to Ready-Mixed Concrete |
|
| FC-13 FAQs on Floor Joint Spacing with Fibers |
|
| FC-14 Blended Fiber Systems for Concrete Reinforcement |
|
| FC-15 Engineering Design Tables for Nudura® ICF WALLS with TUF-STRAND SF™ |